Microchip DSPIC33FJ128GP804-H/PT

DSPIC33FJ128GP804-H/PT General Description

Tailored for demanding applications, the dsPIC33FJ128GP804-H/PT microcontroller from Microchip Technology offers a powerful solution for DSP tasks. With a high-performance DSP engine, advanced analog peripherals, and a high level of integration, this microcontroller delivers exceptional performance in a compact form factor. Featuring 128 KB of flash memory, 4 KB of RAM, and 9 PWM channels, it is well-equipped for tasks such as motor control, power management, and digital audio processing. Additionally, with a 16-bit ADC, multiple communication interfaces, and a small 44-pin TQFP package, the dsPIC33FJ128GP804-H/PT is a versatile choice for space-constrained applications that require precise control and real-time signal processing

Features

• Operating Range
• Up to 40 MIPS operation (at 3.0-3.6V)
• 3.0V to 3.6V, -40ºC to +150ºC, DC to 20 MIPS
• 3.0V to 3.6V, -40ºC to +125ºC, DC to 40 MIPS
• High-Performance dsPIC33FJ core
• Modified Harvard architecture
• C compiler optimized instruction set
• 24-bit wide instructions, 16-bit wide data path
• Linear program memory addressing up to 4M instruction words
• Linear data memory addressing up to 64 Kbytes
• Two 40-bit accumulators with rounding and saturation options
• Indirect, Modulo and Bit-reversed addressing modes
• 16 x 16 fractional/integer multiply operations
• 32/16 and 16/16 divide operations
• Single-cycle multiply and accumulate (MAC) with accumulator write back and dual data fetch
• Single-cycle MUL plus hardware divide
• Up to ±16-bit shifts for up to 40-bit data
• On-chip Flash and SRAM
• Direct Memory Access (DMA)
• 8-channel hardare DMA
• Up to 2 Kbytes dual ported DMA buffer area (DMA RAM) to store data transferred via DMA
• Most peripherals support DMA
• Timers/Capture/Compare/PWM
• Up to five 16-bit and up to two 32-bit Timers/Counters
• One timer runs as a Real-Time Clock with an external 32.768 kHz oscillator
• Input Capture (up to four channels) with Capture on up, down or both edges
• 16-bit capture input functions
• 4-deep FIFO on each capture
• Output Compare (up to four channels) with Single or Dual 16-bit Compare mode and 16-bit Glitchless PWM mode
• Hardware Real-Time Clock/Calendar (RTCC)
• Interrupt Controller
• 5-cycle latency
• 118 interrupt vectors
• Up to 49 available interrupt sources
• Up to three external interrups
• Seven programmable priority levels
• Five processor exceptions
• Digital I/O
• Peripheral pin Select functionality
• Up to 35 programmable digital I/O pins
• Wake-up/Interrupt-on-Change for up to 21 pins
• Output pins can drive from 3.0V to 3.6V
• Up to 5V output with open drain configuration
• All digital input pins are 5V tolerant
• 4 mA sink on all I/O pins
• System Management
• Flexible clock options: External, crystal, resonator and internal RC
• Fully integrated Phase-Locked Loop (PLL)
• Extremely low jitter PLL
• Power-up Timer
• Oscillator Start-up Timer/Stabilizer
• Watchdog Timer with its own RC oscillator
• Fail-Safe Clock Monitor
• Reset by multiple sources
• Power Management
• On-chip 2.5V voltage regulator
• Switch between clock sources in real time
• Idle, Sleep, and Doze modes with fast wake-up
• Analog-to-Digital Converters (ADCs)
• 10-bit, 11 Msps or 12-bit, 500 Ksps conversion
• Two and four simultaneous samples (10-bit ADC)
• Up to 13 input channels with auto-scanning
• Conversion start can be manual or synchronized with one of four trigger sources
• Conversion possible in Sleep mode
• Other Analog Peripherals
• Two analog comparators with programmable input/output configuration
• 4-bit DAC with two ranges for analog comparators
• 16-bit dual channel 100 Ksps audio DAC
• Data Converter Interface (DCI) module
• Codec interface
• Supports I2S and AC.97 protocols
• Up to 16-bit data words, up to 16 words per frame
• 4-word deep TX and RX buffers
• Communication Modules
• 4-wire SPI (up to two modules) with I/O interface to simple codecs
• I2C™ with Full Multi-Master Slave mode support, slave address masking, 7-bit and 10-bit addressing, integrated signal conditioning and bus collision detection
• UART (up to two modules) with LIN bus support, IrDA® and hardware flow control with CTS and RTS
• Enhanced CAN (ECAN) module (1 Mbaud) with 2.0B support
• Parallel Master Slave Port (PMP/EPSP)
• Programmable Cyclic Redundancy Check (CRC)
• Debugger Development Support
• In-circuit and in-application programming
• Two program breakpoints
• Trace and run-time watch

Specifications